Re: 問題ID: 12717 フレームリレーにおけるDLCIとは?
takamoto463
居住地: 大阪
投稿数: 177
追記:すみません。
R2で、サブインターフェースs0/0.3のところをs0/0.2で設定していました。
そこで、サブインターフェースをnoコマンドで
削除したのですが、まずかったようで、
「Not all config may be removed and may reappear after reactivating the sub-interface」
(すべてのコンフィグは削除されるとは限らないかもしれないし、サブインターフェースを復活した後に再現するかもしれません。)
2(config)#int s0/0
R2(config-if)#no int s0/0.2
Not all config may be removed and may reappear after reactivating the sub-interface
R2(config)#show run
^
% Invalid input detected at '^' marker.
R2(config)#do show run
Building configuration...
(省略)
interface Serial0/0
no ip address
encapsulation frame-relay
clock rate 2000000
!
interface Serial0/0.1 point-to-point
ip address 192.168.12.2 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 201
!
interface Serial0/0.3 point-to-point
ip address 192.168.23.2 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 203
!
一応、show runの表示上は削除されたっぽいのですが、
それでも、設定が残ってたりすることは
あるのでしょうか?
それと、s0/0.2の削除はどうやるべきだったのでしょうか?
clear?
erase?
いろいろと、使い分けがあるみたいですが皆さんはどうやって
覚えてるのでしょう?
修正後
R1(S0/0)−R2(S0/0.1)疎通あり
R1(S0/0)−R2(S0/0.3)疎通なし
R2(S0/0)−R1(S0/0) 疎通あり
R2(S0/0)−R3(S0/0) 疎通あり*
R3(S0/0)−R1(S0/0) 疎通なし
R3(S0/0)−R2(S0/0.1)疎通なし
R3(S0/0)−R2(S0/0.3)疎通あり*
以上、よろしくお願いします。
R2で、サブインターフェースs0/0.3のところをs0/0.2で設定していました。
そこで、サブインターフェースをnoコマンドで
削除したのですが、まずかったようで、
「Not all config may be removed and may reappear after reactivating the sub-interface」
(すべてのコンフィグは削除されるとは限らないかもしれないし、サブインターフェースを復活した後に再現するかもしれません。)
2(config)#int s0/0
R2(config-if)#no int s0/0.2
Not all config may be removed and may reappear after reactivating the sub-interface
R2(config)#show run
^
% Invalid input detected at '^' marker.
R2(config)#do show run
Building configuration...
(省略)
interface Serial0/0
no ip address
encapsulation frame-relay
clock rate 2000000
!
interface Serial0/0.1 point-to-point
ip address 192.168.12.2 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 201
!
interface Serial0/0.3 point-to-point
ip address 192.168.23.2 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 203
!
一応、show runの表示上は削除されたっぽいのですが、
それでも、設定が残ってたりすることは
あるのでしょうか?
それと、s0/0.2の削除はどうやるべきだったのでしょうか?
clear?
erase?
いろいろと、使い分けがあるみたいですが皆さんはどうやって
覚えてるのでしょう?
修正後
R1(S0/0)−R2(S0/0.1)疎通あり
R1(S0/0)−R2(S0/0.3)疎通なし
R2(S0/0)−R1(S0/0) 疎通あり
R2(S0/0)−R3(S0/0) 疎通あり*
R3(S0/0)−R1(S0/0) 疎通なし
R3(S0/0)−R2(S0/0.1)疎通なし
R3(S0/0)−R2(S0/0.3)疎通あり*
以上、よろしくお願いします。
投稿ツリー
-
問題ID: 12717 フレームリレーにおけるDLCIとは?
(takamoto463, 2013-11-20 17:56)
- Re: 問題ID: 12717 フレームリレーにおけるDLCIとは? (arashi1977, 2013-11-20 19:34)
-
Re: 問題ID: 12717 フレームリレーにおけるDLCIとは?
(takamoto463, 2013-11-21 15:03)
- Re: 問題ID: 12717 フレームリレーにおけるDLCIとは? (arashi1977, 2013-11-22 9:18)
- Re: 問題ID: 12717 フレームリレーにおけるDLCIとは? (takamoto463, 2013-11-21 16:29)