show interfaces
- モード
- Enable(M)
- デフォルト
- -
- IOS
- 10.0
- 試験レベル
- CCNA
- 構文
- show interfaces [ インタフェース ]
- 使用例
Router#show interfaces serial 0 Serial0 is up*1, line protocol is up*2 Hardware is HD64570, address is 000c.aaaa.bbbb (bia 000c.aaaa.bbbb)*3 Internet address is 192.168.5.2/30*4 MTU 1500 bytes, BW 100000 Kbit*5, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA*6, loopback not set Keepalive set (10 sec) Auto-duplex*7, Auto Speed*8, 100BaseTX/FX*9 ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:05, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec*10 5 minute output rate 0 bits/sec, 0 packets/sec*11 4822 packets input*12, 299644 bytes*13, 0 no buffer Received 1687 broadcasts, 0 ruts, 0 giants, 0 throttles 0 input errors*14, 0 CRC*15, 0 frame*16, 0 overrun, 0 ignored, 0 watchdog*17 4762 packets output*18, 296559 bytes*19, 0 underruns 0 output errors,*20 0 collisions*21, 3 interface resets*22) 0 output buffer failures, 0 output buffers swapped out 3 carrier transitions DCD=up DSR=up DTR=up RST=up CTS=up Router#
*1 該当インターフェースの物理層レベルの状態
*2 該当インターフェースのデータリンク層レベルの状態
*3 該当インターフェースのMACアドレス
*4 該当インターフェースのIPアドレスとサブネットマスク
*5 該当インターフェースの帯域幅
*6 該当インターフェースのL2カプセル化タイプ
*7 二重モードの状態
*8 速度の状態
*9 メディアタイプ
*10 5分間平均の受信ビット数(bps)および受信パケット数(pps)
*11 5分間平均の送信ビット数(bps)および送信パケット数(pps)
*12 受信パケット数
*13 受信バイト数
*14 受信時のエラーパケット数
*15 受信時のCRCエラーカウント数
*16 受信時のフレームエラーカウント数
*17 受信時にWatchdogTimeOutを起こした回数
*18 送信パケット数
*19 送信バイト数
*20 送信時のエラーパケット数
*21 送信時コリジョンが発生し再送した回数
*22 インターフェースをリセットした回数(shotdown/no shutdownを行うとカウントアップ
- 解説
- このコマンドでは、インタフェースの状態や情報を確認することができます。
特定のインタフェースを指定しないで、このコマンドを実行すると、そのデバイスの全てのインタフェースの情報を表示することができます。
- Tips
- 参考リンク
- Google検索
Counter: 51284,
today: 1,
yesterday: 1
最終更新: 2009-08-04 (火) 16:03:05 (JST) (5385d) by staff